Paste: sas smart

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST4000NM003A
Revision:             N004
Compliance:           SPC-5
User Capacity:        4,000,787,030,016 bytes [4.00 TB]
Logical block size:   512 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500ca415aaf
Serial number:        WJG1G4NG0000C0438TWQ
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Thu Oct 16 01:53:13 2025 UTC
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Grown defects during certification <not available>
Total blocks reassigned during format <not available>
Total new blocks reassigned <not available>
Power on minutes since format <not available>
Current Drive Temperature:     26 C
Drive Trip Temperature:        60 C

Manufactured in week 19 of year 2020
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  91
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  298
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 2981695907
  Blocks received from initiator = 2076896717
  Blocks read from cache and sent to initiator = 510978625
  Number of read and write commands whose size <= segment size = 37660747
  Number of read and write commands whose size > segment size = 296034

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 5994.27
  number of minutes until next internal SMART test = 29

Seagate FARM log supported [try: -l farm]

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0          0      16919.791           0
write:         0        0         0         0          0       5465.235           0

Non-medium error count:        0

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background long   Completed                   -      45                 - [-   -    -]
# 2  Background long   Completed                   -      18                 - [-   -    -]
# 3  Background long   Aborted (by user command)   -       9                 - [-   -    -]

Long (extended) Self-test duration: 24343 seconds [6.8 hours]

Background scan results log
  Status: no scans active
    Accumulated power on time, hours:minutes 5994:16 [359656 minutes]
    Number of background scans performed: 0,  scan progress: 0.00%
    Number of background medium scans performed: 0
Device does not support General statistics and performance logging

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: power on
    reason: power on
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500ca415aad
    attached SAS address = 0x500304801b01dd01
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 16
    Phy reset problem count = 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500ca415aae
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization count = 0
    Phy reset problem count = 0